Search for: All records

Previous studies have provided evidence that reinforcement of epoxy adhesives with nanostructures such as carbon nanofibers (CNFs) produces higher strength bonded joints between carbon fiber reinforced polymer (CFRP) laminates and shifts bond-line failure modes from the adhesive into the laminate. Despite this, there has been no research dedicated to applying reinforced adhesives to the bonding of nano-reinforced CFRP such as CNF z-threaded carbon fiber reinforced polymer (ZT-CFRP) laminates, which have been proven to exhibit increased interlaminar shear strength, mode-I delamination toughness, and compressive strength over traditional CFRP. This study examined the effectiveness of using CNF reinforced epoxy adhesives for unidirectional ZT-CFRP laminate bonding through single-lap shear tests using the ASTM D5868-01 standard. Unidirectional CFRP laminate samples bonded with both epoxy adhesive and CNF reinforced epoxy adhesive were also tested for comparison. It was found that the average shear strength observed for ZT-CFRP samples bonded with CNF reinforced epoxy adhesive was approximately 44% and 26 % higher than that of CFRP samples bonded with epoxy adhesive and CNF reinforced epoxy adhesive, respectively. Microscopic image analysis was performed to examine the mode of bond failure. The roles of nanomaterials in the fracture mechanism of the adhesives and the composite laminates are also discussed. 

A film adhesive is commonly used to form the bond line between composite or metal parts. The bond line's quality and performance can be affected by defects such as voids, impurities, agglomerations, and other structural issues found within it; in addition, defects can form due to damage or delamination. Identifying these defects is possible with non-destructive evaluation (NDE). In this paper, the joule-heating effect through carbon nanofibers (CNF) and carbon nanotubes (CNT) modified film adhesive will be used along with infrared thermography for bond line defect inspection. Due to the difference in the electrical conductivity between the modified epoxy and the defect, joule heating can cause a different temperature at the defect; thus, in theory, the defect can be viewed by infrared thermography. The percentage of carbon nanofiller in a film adhesive changes the measurement quality due to its relationship to electrical conductivity. An Acrylonitrile Butadiene Styrene (ABS) equilateral triangle defect with 30 mm sides was used inside bond line samples. These bond lines were composed of epoxy and nanofillers of CNF and CNT at various concentrations. Each concentration was evaluated individually and bonded onto two single-ply CFRP coupons. In this study, the feasibility of using carbon nanofillers of different concentrations as a medium for identifying and characterizing defects through NDE infrared thermography was investigated and validated the effectiveness of this new NDE approach. In the future, aligning nanofiller for bond lines could be a potential research direction to improve upon what this study strives to achieve. 

Carbon fiber reinforced polymer (CFRP) composites have been increasingly used in many vehicles such as airplanes, automobiles, and ships due to the advantages of high-strength, high-modulus, lightweight, and corrosion resistance. CFRP structures enhance the vehicle's performance, energy-efficiency, comfort, and safety. However, a common safety concern is how the CFRP materials perform when the vehicle is in fire and if there are enough time to safely evacuate the passengers. The elevated temperature can soften and decompose the polymer matrix, delaminate the CFRP laminate, and burn the CFRP through the contact with oxygen. As a result, the thermal and flammability response of CFRP is important for considering CFRP for vehicle applications; and some specialty high-temperature or flame/smoke/toxicity-proven resins have been investigated for CFRP parts manufacturing due to the needs. In this paper, a novel flame resistant hypothesis of utilizing the unique nano/micro- interlocked fiber reinforcing structure of the long-range carbon nanofiber z-threaded CFRP (ZT-CFRP) composite laminates for improving the flammability performance will be investigated. The carbon nanofibers (CNT) and carbon nanotubes (CNT), which have excellent thermal and mechanical properties, will be dispersed in an epoxy resin and will zig-zag thread through a carbon fiber fabric using an electrical/flow assisted impregnation process to create the unidirectional ZT-CFRP prepregs, respectively, which will be further processed into ZT-CFRP composite laminates. The UL-94 flammability test will be employed to characterize the ZT-CFRP laminates' flammability performance against the control baseline data of the regular CFRP, all without using any flame retardant chemicals. An impressive self-extinguishing flammability characteristic of the CNF based ZT-CFRP samples has been distinctly identified from all the samples. The UL-94 testing results and the effectiveness of using the long-range nanofiber z-threading strategy for enabling the novel nano/microstructure-induced flame resistant and self-extinguishing characteristics will be discussed. 

Moisture is a known issue for carbon fiber reinforced polymer (CFRP) manufacturing. During the process, in which a CFRP prepreg is carefully thawed, cut, stacked, and cured into a laminate, any bad moisture control can cause voids, affect the curing, and degrade the laminate. Recent studies of carbon nanofiber z-threaded CFRP (i.e., ZT-CFRP) prepreg and its laminates showed significant multifunctional improvements in the mechanical strengths, toughness, thermal conductivity, and electrical conductivity. The carbon nanofibers zig-zag thread among the carbon fibers in the through-thickness direction (i.e., z-direction) and mechanically interlock the fiber system together to form an effective 3D-fiber-network reinforced laminate. This paper presents a preliminary experimental study on the ZT-CFRP prepreg when facing the moisture exposure during the prepreg handling and lamination process. Both the ZT-CFRP and traditional CFRP prepregs, subjected to different humidity conditions, will be cut, and cured into laminate samples. The samples will be tested for their interlaminar shear strengths (ILSS) and hardness. Microscope pictures of the samples' fracture patterns will be compared for explaining the combined impact of the moistures and the carbon nanofiber z-threading strategy on the laminates' interlaminar shear strength and curing state. 

Well-dispersed and unaligned multi-walled carbon nanotubes (MCNTs) infused liquid epoxy adhesive have been reported for significantly improving the adhesive-joint of carbon fiber reinforced polymer (CFRP) composite laminates. However, it has not been determined in the literature if the alignment of MCNTs would provide an additional improvement than the randomly aligned case. In this study, various epoxy film adhesives embedded with 1wt% through-thickness aligned MCNTs, unaligned MCNTs, aligned carbon nanofibers (CNFs), and unaligned CNFs were used for bonding CFRP laminates. These variants have been used to bond two CFRP laminates for the ASTM D5868-01 single lap test as well as a steel variant for the same bonding process. The average shear strengths of the samples bonded by the various film adhesives were compared with the samples bonded by the pure epoxy-films. Microscopic analysis has been used to examine the fracture surface after testing. It was also used to visualize how the film adhesives fail while experiencing shear. This study has investigated the effectiveness of infusing through-thickness directionally aligned vs. unaligned nanoparticles in an epoxy film adhesive for bonding CFRP laminates and steel plate. It also indicates the potential future research direction of using nanoparticles in advanced adhesive technologies. 

Human health and livelihoods are threatened by declining marine fisheries catches, causing substantial interest in the sources and dynamics of fishing. Catch analyses in individual exclusive economic zones (EEZs) and the high seas are abundant, and research across multiple EEZs is growing. However, no previous studies have systematically compared catches, intranational versus international fish flows, and fishing nations within all of the world’s EEZs and across adjacent and distant EEZs and the high seas to inform “metacoupled” fisheries management. We use the metacoupling framework—a new approach for evaluating human–nature interactions within and across adjacent and distant systems (metacouplings)—to illustrate how fisheries catches were locally, regionally, and globally interconnected in 1950–2014, totaling 5.8 billion metric tons and increasing by 298% (tonnage) and 431% (monetary value) over this time period. Catches by nations in their own EEZs (largest in Peru) and adjacent EEZs (largest in Indonesia) constituted 86% of worldwide catches, growing in 1950–1996 but declining in 1997–2014. In contrast, catches in distant EEZs and the high seas—largest in Morocco, Mauritania, and Canada—peaked in 1973 and have since represented 9–21% of annual catches. Our 65-year, local–regional–global analysis illustrates how metacoupled fisheries governance—holistic management of multiscalar catches, flows, and tradeoffs within and among fisheries—can improve food and nutrition security, livelihood resilience, and biodiversity conservation across the world. 

In the 12 years since Dudgeonet al. (2006) reviewed major pressures on freshwater ecosystems, the biodiversity crisis in the world's lakes, reservoirs, rivers, streams and wetlands has deepened. While lakes, reservoirs and rivers cover only 2.3% of the Earth's surface, these ecosystems host at least 9.5% of the Earth's described animal species. Furthermore, using the World Wide Fund for Nature's Living Planet Index, freshwater population declines (83% between 1970 and 2014) continue to outpace contemporaneous declines in marine or terrestrial systems. The Anthropocene has brought multiple new and varied threats that disproportionately impact freshwater systems. We document 12 emerging threats to freshwater biodiversity that are either entirely new since 2006 or have since intensified: (i) changing climates; (ii) e‐commerce and invasions; (iii) infectious diseases; (iv) harmful algal blooms; (v) expanding hydropower; (vi) emerging contaminants; (vii) engineered nanomaterials; (viii) microplastic pollution; (ix) light and noise; (x) freshwater salinisation; (xi) declining calcium; and (xii) cumulative stressors. Effects are evidenced for amphibians, fishes, invertebrates, microbes, plants, turtles and waterbirds, with potential for ecosystem‐level changes through bottom‐up and top‐down processes. In our highly uncertain future, the net effects of these threats raise serious concerns for freshwater ecosystems. However, we also highlight opportunities for conservation gains as a result of novel management tools (e.g. environmental flows, environmental DNA) and specific conservation‐oriented actions (e.g. dam removal, habitat protection policies, managed relocation of species) that have been met with varying levels of success. Moving forward, we advocate hybrid approaches that manage fresh waters as crucial ecosystems for human life support as well as essential hotspots of biodiversity and ecological function. Efforts to reverse global trends in freshwater degradation now depend on bridging an immense gap between the aspirations of conservation biologists and the accelerating rate of species endangerment.